Current to Pressure (I/P) Converter - NOT CE Compliant - Not for sale in UK/EU

IP210

Current to Pressure (I/P) Converter | Omega Engineering

スクロールダウンし、全ラインアップをご覧ください

注文する

Loop Power I to P converter
Ideal for Pneumatic Control Systems
IP65 Sealed Case
Zero and Span Adjustments for Field Calibration
Rugged Zinc Cast Housing

制御・電磁弁 (バルブ) / 調整器 - 関連する商品を探す
（見つからない場合はカスタマーサービスにご連絡ください）

商品説明

The IP210 series has been replaced by our new IP210A series below that performs the same function and comes at a lower price point.

A “current to pressure” (I/P) converter converts an analog signal (4 to 20 mA) to a proportional linear pneumatic output (3 to 15 psig). Its purpose is to translate the analog output from a control system into a precise, repeatable pressure value to control pneumatic actuators/operators, pneumatic valves, dampers, vanes, etc. The IP210 is a loop-powered instrument, which eliminates the need for an external power supply (except for IP210-X120).

Principle of Operation
OMEGA's IP210 converts an analog signal (4 to 20 mA) to a proportional linear pneumatic output (3 to 15 psig). Its uncomplicated design and proven electromagnetic force balance deliver consistently high performance.

The IP210 provides a reliable, repeatable, accurate means of converting an electrical signal into pneumatic pressure. Its force balance principle is a coil suspended in a magnetic field on a flexible mount. At the lower end of the coil is a flapper valve that operates against a precision ground nozzle to create a backpressure on the servo diaphragm of a booster relay.

The input current flows in the coil and produces a force between the coil and the flapper valve, which controls the servo pressure and the output pressure.

Zero adjustment of the unit is made by turning a screw that regulates the distance between the flapper valve and the air nozzle. Span adjustment is made by varying a potentiometer, which shunts input current past the coil. An integral volume flow booster provides adequate flow capacity, resulting in fast response time and accurate control.

SPECIFICATIONS
Accuracy: 0.5% FS
Supply Sensitivity: 0.025% span per % supply pressure change
Zero Adjustment: 5% FS
Span Adjustment: 20% FS
Operating Temp: -20 to 70°C (-5 to 160°F)
Compensated Temp: -10 to 60°C (15 to 140°F)
Thermal Effects: <0.1%/°C over operating range
Input Resistance: <300 Ω
Media: Oil-free, clean, dry air filtered to 25 µm
Recommended Supply Pressure: 25 to 30 psig (filtered air)
Max Supply Pressure: 80 psig (for IP210-X120: 135 psi)
Min Supply Pressure: 10 psi above maximum output pressure
Air Consumption (Leakage): 0.03 scfm
Flow Rate: 10 scfm ≤60 psi; 0.06 <60 psi
Response Time:
<30 psi: less than 0.5 s (10 to 90% step)
≥30 psi: 2 s
Failure Mode: Upon electrical failure, the signal pressure falls to bleed pressure
Pressure Port: ¼ FNPT
Electrical Connection: DIN 43650 with screw terminals included
Housing: IP65 rated, epoxy-painted zinc die castings
Construction: Nitrile diaphragms, stainless steel/nylon flapper, nozzle and supply valve, integral surface mounting bracket included
Weight: 1.7 kg (3 lb)

注文する（部品番号ビルダーより掲載以外の製品もご選択いただけます）(注文数を入力の上、"カートに追加"をクリックしてください)

部品番号/Desc.

注文数

商品説明

IP210-X15

お問い合せ下さい

納期:

Current to pressure (I/P) converter with 2 wire 4-20 mA input and 3-15 psig output

IP210-X30

お問い合せ下さい

納期:

Current to pressure (I/P) converter with 2 wire 4-20 mA input and 3-30 psig output

IP210-X60

お問い合せ下さい

納期:

Current to pressure (I/P) converter with 2 wire 4-20 mA input and 3-60 psig output

IP210-X120

お問い合せ下さい

納期:

Current to pressure (I/P) converter with 3 wire 4-20 mA input and 3-120 psig output (12-24 volt external power supply required)

IP210A-X15

¥133,631 (税込)
(税抜価格 ¥121,483)

納期: 2 週間

Current to Pressure (I/P) Converter

IP210A-X30

¥133,631 (税込)
(税抜価格 ¥121,483)

納期: 2 週間

Current to Pressure (I/P) Converter

IP210A-X60

¥133,631 (税込)
(税抜価格 ¥121,483)

納期: 2 週間

Current to Pressure (I/P) Converter

IP210A-X120

¥138,769 (税込)
(税抜価格 ¥126,154)

納期: 2 週間

Current to Pressure (I/P) Converter

注: IP210-X120 uses 3 wire 4-20 mA connection with external 12 to 24 volt power supply. All other models are 2 wire loop powered models.