フリーダイヤル 0120-769-103
Emailjpesales@dwyeromega.com

Thermal Dispersion Flow Switches

FSW-6000 and FSW-7000 Series

Thermal Dispersion Flow Switches | FSW-6000 and FSW-7000 Series

Thermal Dispersion Flow Switches

¥173,505 FSW-6212

1 year warranty
  • Simple to Install and Low Cost
  • No Moving Parts-Maintenance Free Reliability
  • Optimal Temperature Compensation — Unaffected by Temperature Gradient
  • Can Operate in Temperatures up to 120°C (248°F) with Sanitary Option
  • Have a Maximum Working Pressure of 4,300 PSI (300 bar)
  • Chain of 8 LEDs- Integrated Flow Rate/Setpoint Indication
  • Can Be Used as a Level Switch
ロタメータ / 流量スイッチ - 関連する商品を探す
(見つからない場合はカスタマーサービスにご連絡ください)

商品説明

The FSW-6000/7000 Series are thermal flow switch monitors designed to monitor flow status and also used to detect level of liquids, air and gas. A chain of 8 LED’s gives the user a visual indication of the flow rate. In addition, there isalso a dichromatic LED, which shows the switch point status of the unit. The sensing element and connection of the FSW-6000/7000 Series are made with 316 SS. The standard enclosure is glass-filled nylon and is also available in an aluminum enclosure for hazardous environments. The FSW-6000/7000 Series can be made with a great variety of process connections such as threaded, flange, or sanitary.

The FSW-6000/7000 Series line of thermal flow switch monitors is based on the principle of thermal dispersion. A typical configuration uses two platinum Resistance Temperature Detectors (RTD’s) set within the tip of the sensor. One RTD is heated a few degrees above the temperature of the medium and the other RTD is used as a reference, sensing the actual process temperature. The second RTD also monitors the temperature of the medium, as any changes in temperature must be compensated for in the first RTD. As the process medium flows over the tip of the sensor it disperses some of theheat from the first RTD. The temperature change between the two RTD's signals the probe’s electronics and the switch changes state once the set point has reached.

The FSW-6000/7000 Series may be installed in a pipe or tank using the thread or connection provided. Use only the hexagon when tightening to achieve a seal, do not use the body. The body should be rotated after tightening to leave the cable gland in suitable orientation. The FSW-6000/7000 Series is not affected by its fixing position so it may be installed at any angle around the pipe. However, it is recommended that with horizontal pipe runs the sensor should be installed on the side, into the middle of the pipe. In vertical pipes, the FSW-6000/7000 Series should be installed when there is flow in an upward direction against gravity. Care should be taken when installing the sensor that the probe extends clear of the pipe’s internal wall and is fully immersed into the flow. In pipes with smaller diameters, some care should also be taken so that the sensor is not screwed too far into the line.

SPECIFICATIONS
Accuracy: ±10% of setpoint
Repeatability: ±1% of setpoint
Power Supply:
    FSW-6000: 85 to 240 Vac (50/60 Hz)
    FSW-7000: 24 Vdc ±10%
Temperature Range:
    Process: -20 to 80°C (-4 to 176°F) [sanitary option to 120°C (248°F) for CIP]
    Operating: -20 to 60°C (-4 to 140°F)
Max Pressure: 300 bar (4351 psi)
Protection Class: NEMA 4 (IP65)
Wetted Materials: 316 SS
Enclosure Material: Glass filled nylon standard or aluminum die cast option
Process Connection: ½ to 1½ NPT, Tri-Grip™, or flange (others available, consult Flow Engineering Department)
Output: 250 Vac SPDT 5 A relay
Switch Point Adjustment: Potentiometer
Bargraph:
    Green LED: Flow rate above setpoint
    Yellow LED: Flow is at above setpoint
    Red LED: Flow is below setpoint
Switch Point Status:
    Red LED: No flow
    Green LED: Flow
Response Time: 1 to 10 seconds
Max Start up Delay: 12 seconds
Switching Range: 3 cm/s to 3 m/s (0.09 to 9.84 ft/sec) (liquid), 5 cm/sec to 15 m/sec (0.16 to 49 ft/sec) (gas)
Dimensions:
    Nylon Head: 88 Dia x 80 mm H (3.5 x 2.5" H)
    Aluminum Head: 88 Dia x 108 mm H (3.5 x 4.25")
    Insertion Length: 138, 2 and 3" standard, for other lengths consult Flow Engineering
     Maximum insertion Length is 36"

    Weight: Approx 680 g (1.5 lb)
注文する (部品番号ビルダーより掲載以外の製品もご選択いただけます)(注文数を入力の上、"カートに追加"をクリックしてください)

他のお客様はこのような商品も購入しています。: このアイコンをクリックすると、このモデルを購入した他のお客様の購入商品リストが表示されます.

部品番号/Desc.
注文数
商品説明
  
FSW-6212
¥190,856 (税込)
(税抜価格 ¥173,505)
納期: 8 週間
 
85 to 240 Vac, 3/4 NPT, 2" length, glass filled nylon with 1/2 NPT conduit, cable gland, and 2 m (6.5') cable. For 1" to 4" pipes
  
FSW-6222
¥179,960 (税込)
(税抜価格 ¥163,600)
納期: 8 週間
 
85 to 240 Vac, 3/4 NPT, 2" length aluminum die cast with 1/2 NPT conduit, and 2 m (6.5') cable. For 1" to 4" pipes
  
FSW-6512
¥209,017 (税込)
(税抜価格 ¥190,015)
納期: 8 週間
 
85 to 240 Vac, 1-1/2 Tri-Grip™, 2" length, glass filled nylon with 1/2 NPT conduit with cable gland, and 2M (6.5') cable. For 1 to 4" pipes
  
FSW-7111
¥190,856 (税込)
(税抜価格 ¥173,505)
納期: 7 週間
 
24 Vdc, 1/2 NPT, 35 mm (1 3/8") length, glass filled nylon with 1/2 NPT conduit with cable gland, 2m (6.5') cable. For pipes up to 1"
  
FSW-7112
¥157,839 (税込)
(税抜価格 ¥143,490)
納期: 8 週間
 
24 Vdc, 1/2 NPT, 50 mm (2") length, glass filled nylon with 1/2 NPT conduit with cable gland, 2m (6.5') cable. For 1" to 4" pipes
  
FSW-7121
¥179,960 (税込)
(税抜価格 ¥163,600)
納期: 8 週間
 
24 Vdc, 1/2 NPT, 35 mm (1-3/8") length, aluminum die cast with 1/2 NPT conduit, 2 m (6.5') cable. For 1" to 4" pipes
  
FSW-7122
¥179,960 (税込)
(税抜価格 ¥163,600)
納期: 8 週間
 
24 Vdc, 1/2 NPT, 50 mm (2") length, aluminum die cast with 1/2 NPT conduit, 2 m (6.5') cable. For 1" to 4" pipes
Accessories
Click to expand/minimize a list of what others bought with the70A-1
70A-1
¥7,464 (税込)
(税抜価格 ¥6,785)
納期: 2 週間
 
Continuous tone alarm
Click to expand/minimize a list of what others bought with theTX4-100
TX4-100
¥10,603 (税込)
(税抜価格 ¥9,639)
納期: 2 週間
 
30.5 m (100') spool of 4 Conductor Wire
Click to expand/minimize a list of what others bought with theU24Y175
U24Y175
お問い合せ下さい   
納期: 
 
 
24 Vdc power supply
注: Comes complete with operator’s manual.

For "ECTFE/ETFE" element coating, add suffix "-ETFE" to model number, add $200 to price.


Ordering Example: (1) FSW-6212 Flow Switch, ¥173,505

部品番号ビルダー

下記から仕様構成を選択し、ご注文ください
以下からオプションを選択:


(1) Power :
6 : 85 to 240 Vac
7 : 24 Vdc ± 10%

(2) Process Connection :
1 : 1/2 NPT thread
2 : 3/4 NPT thread
3 : 1 NPT thread
5 : 1-1/2" Tri-Grip
6 : 2" ANSI flange

(3) Enclosure :
1 : Glass filled nylon with 1/2 NPT conduit and cable gland
2 : Aluminum die cast with 1/2 NPT conduit
3 : Aluminum die cast with cable gland

(4) Insertion Length :
1 : 35 mm (1-3/8")
2 : 50 mm (2")
3 : 75 mm (3")
注: 有効な部品番号については、「商品仕様(PDF)」を参照ください。
ご不明な場合は、カスタマーサービス(0120-040-572 もしくは jpesales@dwyeromega.com)へお問合せください。
We noticed you are from the US. Visit your local site for regional offers and live support.