PTFE Liquid Flow Sensors

FPR-1500

スクロールダウンし、全ラインアップをご覧ください

注文する

Provides Highly Linear 0 to 5 Vdc Output Signal and Buffered Linear Pulse Output Signal for Totalizing
Micro-Liquid Flow Rates as Low as 15 ml/min Can Be Measured with High Precision
Usable with a Variety of Low Viscosity Liquids Including Many Corrosive Liquid Chemicals

タービン流量計 (羽根車式) - 関連する商品を探す
（見つからない場合はカスタマーサービスにご連絡ください）

商品説明

FPR1501 Series flow sensors can measure extremely low flow rates from 15 mL/min. They are suitable for a wide variety of industrial, commercial, and laboratory flow applications.

Because the FPR1501 flow sensors have only PTFE and sapphire wetted surfaces, it is anticipated that they will replace conventional glass tube and ball flowmeters in many applications in which an electrical signal proportional to flow rate is desirable, even in very corrosive applications in which the liquid is low in viscosity (i.e., less than 10 centistokes).

Models use a Pelton-type turbine wheel to determine the flow rate of the liquid. The rotation rate of the turbine wheel is linear over a large dynamic range. The electro-optical system consists of a diode emitting energy in the infrared spectrum. Light energy is interrupted and passed from 8 small holes in the small turbine wheel. This reflected light energy is detected by a photodiode. Thus, as the turbine wheel rotates in response to the liquid flow rate, electrical pulses are generated. Processing circuitry provides a DC voltage output and buffered square-wave output pulses that are proportional to the flow rate.

Tube Fitting:
1/8" tube fittings for flowrates up to 100 ml/min
¼" tube fitting for flow rates from 100 ml/min. to 2 liters/min
3/8" tube fitting for flow rates greater than 2 liters/min.

SPECIFICATIONS
Output Signal: 0 to 5 Vdc, adjustable ±20% (typical) and pulse output from 0 to 300/500 pps (typical) @ 7.5 Vdc peak pulse height-linear
Power Requirements: 12 to 15 Vdc regulated, 50 mA
Standard Sensor Material: PTFE, sapphire, Perfluoroelastomer gasket; PFA compression tube fittings
Pressure Rating: 4 bar (60 psig) max
Temperature Rating: 0 to 70°C (32 to 158°F)
Temperature Sensitivity: ±0.2%/°C
Accuracy: ±3% FS
Repeatability: ±0.2% FS from 20 to 100% of rated max flow
Dimensions: 55.6 x 48.0 x 58.9 mm (2.19 x 1.89 x 2.32") not including fittings
Applicable Liquids: Many low-viscosity (<10 centistokes) liquids; check compatibility with wetted materials; specify liquid when ordering

注文する（部品番号ビルダーより掲載以外の製品もご選択いただけます）(注文数を入力の上、"カートに追加"をクリックしてください)

他のお客様はこのような商品も購入しています。: このアイコンをクリックすると、このモデルを購入した他のお客様の購入商品リストが表示されます.

部品番号/Desc.

注文数

商品説明

FPR1501

お問い合せ下さい

納期:

15 to 100 ml/min, 1/8" tube fitting

FPR1502

お問い合せ下さい

納期:

25 to 200 ml/min, 1/4" tube fitting

FPR1503

お問い合せ下さい

納期:

50 to 500 ml/min, 1/4" tube fitting

FPR1504

お問い合せ下さい

納期:

100 to 1000 ml/min, 1/4" tube fitting

FPR1505

お問い合せ下さい

納期:

0.2 to 2.0 l/min, 1/4" tube fitting

FPR1506

お問い合せ下さい

納期:

0.5 to 5.0 l/min, 3/8" tube fitting

ACCESSORIES

FPR1500-PW

お問い合せ下さい

納期:

Power supply, 115 Vac to 12 Vdc

FPR1500-230PW

お問い合せ下さい

納期:

Power supply, 230 Vac to 12 Vdc, with European plug

DP25B-E

¥81,994 (税込)
(税抜価格 ¥74,540)

納期: 4 週間

Analog input panel meter with 12 volt excitation

注: Comes complete with 0.9 m (3') long cable with pigtails and operator's manual.

Note: Maximum differential pressure (delta P) across flow sensor occurs at maximum rated flow using water at 23°C (73°F). At 50% of rated flow,delta P is 0.25 of value at max. rated flow, and, at 20% of rated flow, delta P is 0.04 of value at max. rated flow.

Ordering Example: (1) DP25B-E 1/8 DIN Panel meter with 12 volt excitation, ¥74,540